Leading 10 usual forklift crashes ， forklift procedure must take notice of these issues ！.

Don't underestimate the forklift at the workplace. If the procedure is not good, there will be serious mishaps in minutes, and there are lots of mishaps including forklifts.

Instance 1: The forklift freight obstructed the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which practically triggers an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Situation 7: The forklift driver did not put on a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure should pay attention to these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before beginning.
3. When the forklift starts with a tons, the driver needs to first validate that the load is steady and reputable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted in reverse. .
2. Do not raise the fork too high when driving. When getting in and leaving the job site or while driving, beware that there will certainly be no obstacles overhead. When the lots is traveling, the fork needs to not be elevated too high, which will influence the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly create the vehicle to lose side security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and have to maintain a particular safety and security range from the car in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry should be correctly tilted back. The load shall not be raised other than when piling or filling. .
8. The elevation of the tons need to not block the chauffeur's sight. In special circumstances, when the item influences the forward vision, drive at a reduced rate when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory area is 5 km/h, and it has to drive securely at a low speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to base on the fork to hold items and play a stabilizing function. .
12. If issues are found, they will certainly be repaired and reported in a timely fashion, and they will certainly never run with health problems or hide them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks need to be readjusted as needed to make the tons of the two forks well balanced and not skewed, and one side of the item need to be against the shelf. .
2. It is prohibited to work with a solitary fork or utilize a fork top or draw. In special circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch other products or things. The load must be maintained with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted ahead a little when the load is reduced to permit easy placement of the lots and removal of the forks. .
6. It is restricted to fork goods at high speed and hit tough things with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so regarding avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to engage in high-altitude operations to prevent high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, put, round or roll objects. .
10. It is not allowed to use forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Pull the emergency brake deal with to dead or dispirit the emergency brake button.
3. The engine is shut off and the power is removed. (Except for special situations, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look needs to be inspected, and gas, lubricating oil and cooling water should be included.
2. Examine the security performance of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leak ought to also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline should be slow-moving and uniform, and no activating the slope is allowed.
7. Do not drive throughout the slope. When the slope is greater than 10%, the automobile ought to be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not allowed.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing Stand-on Electric Pallet Stacker on the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not enabled to make use of inertia Electric Forklift Truck for Warehouse force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not allowed to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is increased.
8. Do not drive laterally on inclines
.
Car parking is not permitted under the list below problems.
1. Contours, slim roads, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the opposite side of the section with the same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844